Replacing a critical component can be difficult to get right, especially if you do not have the original machine specifications. Thankfully, there are a few ways to identify oil seals; from their design, size and material. As there are hundreds of different oil seals available on the market, this guide will cover the four most common design types. Typically available with either a single or double lip, in Nitrile or Viton Rubber Material.

Oil Seal Single Lip vs Double Lip

Firstly, the oil seals covered in this guide classify the single lip as the inner diameter at the bottom of the component. The single lip is vital to the function of the seal by containing the oil, grease or lubricant. The only difference between a single and double lip is the additional rubber lip on the top of the oil seal which helps prevent dust or dirt from coming close to the shaft. Identifying the oil seal lip can be misinterpreted with a visual inspection alone. For or this reason, you should press along the inner diameter at the top of the seal, if you feel a ridge with a slight movement or give it is highly likely you have a double lipped oil seal.

Industry retailers use unique codes to identify oil seals worldwide. The most common lip style designations are 21 (single lip) and 23 (double lip), please read our Oil Seal Cross Reference Guide for more detailed information.

 

Identify Oil Seal Design

1. Type A - Rubber Covered Lip Seals

Fully covered outer diameter for excellent sealing. This oil seal is fully enclosed in a rubber material and is the most widely used type of oil seal. Great resistance to thermal cycling, temperatures and different chemical resistance.

2. Type B - Metal Outer Diameter Oil Seals

Economic metal outer diameter for standard applications. This is an economical oil seal where the metal is exposed on one side and offers a closer fitting between the oil seal and housing or bore. Due to this, it has limited use with sealing thin liquids or gases.

3. Type C - Reinforced Metal Insert Oil Seals

The same design as type B with an additional inner case for greater structural rigidity. This type of oil seal is typically used in heavy-duty engineering machinery or large diameter sized seals

4. Type F - Stainless Steel Garter Spring

The same design as type A with corrosion protected metal case and stainless-steel garter spring. Suitable for use with a wide range of fuels and chemicals.

 

Identify Oil Seal Material

Nitrile or NBR is black in colour, whereas, Viton or FKM is usually a brownish colour. To understand the main comparisons between the two compounds read our Nitrile vs. Viton article.

 

How to Measure Oil Seals

Finally, Polymax part codes follow the same pattern as our O-rings - inner diameter, outer diameter and height. This is different from the industry-standard convention, whereby imperial oil seals follow - outer diameter, inner diameter and height.

We hope the information in this article helps you identify the correct oil seal for your application. If you have any queries feel free to call one of our sales engineers on 01420 482862. Polymax stock over 6,000 oil seals available to buy online, browse our oil seal selection today.

Different Types of Automotive Oil Lip Seals

Oil Seals

Nov 09, 2015

Oil seals are used in applications that require part of the system to be sealed off. Lip seals allow the application to be secured against high pressures, since they offer tighter sealing action. Several types of oil lip seals have been developed that allow users to choose the right type of sealing effect they would expect in an application. Automotive oil lip seals are available in various configurations to support multifarious industries and their varied requirements.

What are Automotive Oil Seals?

Since several liquids are present in an automotive application, oil lip seals are extremely useful. They help in separating liquids as well as prevent leakages. In an automotive application, one cannot afford to have the different fluids mix with one another.

Some of these oil lip seals are fabricated with an integrated spring that makes sure that the lip maintains contact with the shaft. This feature is extremely important in critical applications. Automotive oil seal manufacturers can even design and manufacture oil lip seals according to your unique requirements.

What are the Different Types of Automotive Oil Lip Seals?

Several types of oil lip seals are available in the market. They can be made available in several materials and dimensions. They can be fabricated with or without springs. The most commonly used oil lip seals include:

1. External
2. Single
3. Dual
4. Flange Case
5. PTTE and more

The oil lip seal used in an application forms a critical component. It helps in containing an area and as such, the seal should be chosen with care. Of the different types of oil lip seals available, the correct choice will not only depend on the operative requirements of your application but also on the physical dimensions and other design-related factors.

Related Post

Oil seals are widely used as sealing devices for machines.

JTEKT's oil seals are described in our catalog, Oil Seals & O-Rings.
However, the catalog uses a large number of technical terms and is very long, so many people seem to have trouble handling it.

Therefore, this series of columns will summarize the following in order:
• The structure, functions, and types of oil seals
• How to select the right oil seal
• Handling of seals, and causes and countermeasures for oil seal failure

1. What are oil seals?

A wide range of sealing devices are used in various machines.
Sealing devices serve the following functions:

• Prevent leakage of sealed lubricant from inside
• Prevent entry of dust and foreign matter (dirt, water, metal powder, etc.) from outside

As shown in Figure 1, sealing devices come in two types: contact and non-contact.
Oil seals are among the major contact type sealing devices.

Figure 1: Types of sealing devices

Please see the following for the types of sealing devices for bearings.
How to Select the Right Bearing (Part 7): Components surrounding the bearing

2. Oil seal structure and functions

Oil seals come in various shapes to fit the machines and substances to be sealed.
Figure 2 shows the structure and the names of the various components of the most typical oil seal.
The functions of the various components are also indicated in Table 1.

Figure 2: Typically shaped oil seal and component nomenclature

* "KOYO" is a registered trademark of JTEKT.

Table 1: The functions of the various components

No.

Name

Functions

①

Main lip The main lip is the most critical component of the seal.

Its sealing edge comes in full contact with the shaft surface in order to provide excellent sealing performance.
(See Figure 3.)

②

Minor lip The minor lip prevents the entry of dust and contaminants from outside.
Lubricant can be retained in the space between the main lip and the minor lip.

③

Sealing edge This refers to the component of the oil seal that makes contact with the shaft.
It is wedge-shaped to be pressed against the shaft surface and makes contact with the shaft to ensure sufficient sealing performance and suitability for operation at high peripheral speed.

④

Spring The spring supplements the tightening force (i.e., the lip radial load) to ensure enhanced sealing performance and tight contact between the shaft and the sealing edge.The spring also prevents the deterioration of main lip sealing performance caused by high heat or other such factors.

⑤

Metal case The metal case provides rigidity to the seal, helping it settle on the housing securely. It also ensures easy seal handling and mounting.

⑥

O.D. (outside diameter) surface The O.D. surface affixes the oil seal to the housing and prevents leakage , through the fitting area, of substances to be sealed, while excluding contaminants.

⑦

Fluid side face The front-end face of the seal is called the nose. The nose is made of rubber and forms a gasket seal when compressed on the housing shoulder.

⑧

Air side face The oil seal surface vertical to the center line of the shaft on the side that does not come in contact with substances to be sealed is called the back face.

Figure 3: Sealing function of main lip radial load
* "KOYO" is a registered trademark of JTEKT.

Figure 4 shows the features of a JTEKT oil seal.

Figure 4: JTEKT oil seal features

For more detailed information, please see the following:

Names and functions of seal components　

3. Seal types and numbering system

1) Common seal types and their features

Seals are classified by O.D. wall material, lip type, and whether they have a spring or not.
Major oil seals are specified in ISO 6194-1 and JIS B 2402-1.
Table 2 shows the common types of oil seals, while Table 3 shows the features of each type of oil seal.
Table 4 lists the JTEKT oil seal type codes and corresponding ISO and JIS standards.

Table 2 a): Common types of oil seals (with spring)

With spring Rubber O.D. wall Metal O.D. wall

Metal O.D. wall
(with a reinforcing inner metal case)

Without minor lip


Type code

With minor lip


Type code

Table 2 b): Common types of oil seals (without spring)

Without spring Rubber O.D. wall Metal O.D. wall

Without minor lip

Type code

With minor lip


Type code

Table 3: Features of each seal type

No.

Type

Features

1

With spring type Secures stable sealing performance.

2

Rubber O.D. wall type Provides stable sealing performance around the seal O.D. surface.

3

Metal O.D. wall type Ensures improved fitting retention between the seal O.D. and the housing bore.

4

Metal O.D. wall type (with a reinforcing inner metal case) Protects the main lip.

5

With minor lip type Used for applications where there are contaminants, such as dust and foreign matter, on the air side face of the oil seal.

Table 4: JTEKT oil seal type codes and corresponding ISO and JIS standards

JTEKT

ISO 6194-1 1)

JIS B 2402-1 2) MHS Type 1 HMS Type 2 HMSH Type 3 MH － HM － MHSA Type 4 HMSA Type 5 HMSAH Type 6 MHA － HMA －

Notes
1) ISO: International Organization for Standardization
2) 2) JIS: Japanese Industrial Standard

2) Special seal types and their features

JTEKT provides special seals for use in a wide variety of machines and applications.
Table 5 lists the major special seals, their shapes, and their features.

Table 5: The major special seals, their shapes, and their features

Name Type
(type code) Shape Features

Helix Seal

The hydrodynamic ribsa) provided in one direction on the air side face of the lip ensure higher sealing performance. Perfect Seal The hydrodynamic ribsa) provided in two directions on the air side face of the lip ensure higher sealing performance (higher sealing performance in both rotational directions of the shaft).

Super Helix Seal

The hydrodynamic ribsa) have a two-stepped rib configuration provided in one direction on the air face of the lip. Even if the first rib is worn out, the second rib comes into contact with the shaft surface, meaning that this type of oil seal ensures higher sealing performance. Seal with Side Lip A large side lip ensures prevention of entry of dust/water.

　　　　　　　　　　　　a)

Function of hydrodynamic ribs

For more detailed information, please see the following:

Special seal types and their features

3) Seal numbering system

Figure 5 explains the JTEKT seal numbering system.
Seal numbers consist of
　(1) the seal type code,
　(2) the spring code,
　(3) the lip type code,
　(4) the dimensional numbers, and
　(5) the special type code,
and Table 6 shows examples of each of these codes/numbers.

Figure 5: JTEKT seal numbering system



Table 6: Codes and numbers used in seal numbers

No. Code and number Example ① Seal type code (*)

MH: O.D. wall is a rubber material
HM: O.D. wall is a metal case
MH(S)H: O.D. wall is metal with a reinforced inner metal case

② Spring code

No code: without minor lip

A: with minor lip

③ Lip type code

No code: without minor lip

A: with minor lip

④ Dimensional numbers Shaft number 45: The seal suits the shaft diameter of ϕ45 mm. Housing bore number 70: The seal suits the housing bore diameter of ϕ70 mm. Width number 8: The seal width is 8 mm. ⑤ Special shape code

J: Additional code is added here as an identifier when two or more seals have exactly the same type codes and dimensional numbers.

Note: For seal type codes, see Table 2.

4. Example of the applications of seals

Oil seals are used in a great many machines.

1) Oil seals for cars

Oil seals are used in many areas around the car.
Figure 6 shows the places where each seal type is used.

Figure 6: Oil seals for cars

For more detailed information, please see the following:

Oil seals for cars

2) Oil seals for steel production equipment

Oil seals are used in a great many devices for steel production equipment.
Figure 7 shows the places where each seal type is used in a rolling mill.

Figure 7: Oil seals for steel production equipment (rolling mill)

For more detailed information, please see the following:

Oil seals for steel production equipment

5. Conclusion

Oil seals are one of the major contact type sealing devices.
• They prevent leakage of the lubricant or other sealed substance, and
• prevent entry of dust and foreign matter (dirt, water, metal powder, etc.) from outside.

Oil seals come in various shapes to fit the machine or substance for sealing.
For this reason, when designing a machine, it is important to select the oil seal that is right for that machine.
Next time, we will explain the key points to consider when selecting your oil seal.

If you have any technical questions regarding oil seals, or opinions/thoughts on these "Bearing Trivia" pages, please feel free to contact us using the following form: